FREE SHIPPING!
With this kit, you can easily and quickly have upgraded accuracy when adjusting the on screen image for your Electrohome G07 CBO | CRT monitor.
It is mostly plug and play but, you will need some basic soldering skills to instal one resistor and two jumper. The control board itself plugs right into the existing points on your monitor Electrohome G07 CBO monitor chassis.
If you are already installing a cap kit, this is a must.
Other kits come with easily broken potentiometers. Our kit takes away the need to hold with one finger and adjust.
American designed and assembled. This kit takes quality and craftsmanship to the pinnacle of success. The crimps are each throughly inspected prior to being packaged.
Kit Includes:
Assembled board
One resistor
Two jumpers
Sticky backing
The G07 CBO | CRT monitor is commonly found in Pacman, among other games from the era.
Before ordering, confirm you have an Electrohome G07 CBO.
Ensure you have the technical skills to discharge and work on your monitor chassis.
If you do not, please bring in a professional technician.
If you are proficient at removing your Chassis, you can mail us your chassis for a tuneup. We will install this kit at the same time.
Please reference the installation instructions:
G07-CBO H. V. Mod kit
This mod gives you the ability to freely and smoothly adjust your image on the screen both horizontally and vertically.
Included is all the components to complete the modification
1 - 6.8K 3W resistor
2 - zero ohm jumper wires
1 - H. V. Adjustment board
***Unplug and discharge monitor before installation!!!
Installation instructions are as follows.
1. Desolder and discard R421, R507, R531 and R532
2. Solder in the 6.8k ohm 3W resistor from the kit in location R421
3. Fill the solder holes where R507 and R532 were
4. Desolder the two gray jumper wires from the chassis and discard
5. Install the two 0 ohm jumper wires provided in location R531 and between where the gray V. center wire was removed and the center vertical adjustment post
6. Attach the HV adjustment mod to the six adjustment posts from left to right with the corresponding wires
7. Remove the backing from the foam tape on the back of the adjustment board and attach into place
Note: Pots should already be adjusted to their Center for the first run, if not turn them to their mechanical centers. Afterwards adjust as needed.
Deep 6 Arcade LLC is not responsible and can not be held liable for any damage caused from either this kit or how you install it. By installing this kit you relinquish Deep 6 Arcade LLC from any and all liability.
If you are not training in working on CRT monitors, STOP and have a professional do it for you. Do not attempt to touch or work on any CRT monitors if you are not fully aware of how to safely handle and discharge them as well as perform work on them.
FREE SHIPPING!
With this kit, you can easily and quickly have upgraded accuracy when adjusting the on screen image for your Electrohome G07 CBO | CRT monitor.
It is mostly plug and play but, you will need some basic soldering skills to instal one resistor and two jumper. The control board itself plugs right into the existing points on your monitor Electrohome G07 CBO monitor chassis.
If you are already installing a cap kit, this is a must.
Other kits come with easily broken potentiometers. Our kit takes away the need to hold with one finger and adjust.
American designed and assembled. This kit takes quality and craftsmanship to the pinnacle of success. The crimps are each throughly inspected prior to being packaged.
Kit Includes:
Assembled board
One resistor
Two jumpers
Sticky backing
The G07 CBO | CRT monitor is commonly found in Pacman, among other games from the era.
Before ordering, confirm you have an Electrohome G07 CBO.
Ensure you have the technical skills to discharge and work on your monitor chassis.
If you do not, please bring in a professional technician.
If you are proficient at removing your Chassis, you can mail us your chassis for a tuneup. We will install this kit at the same time.
Please reference the installation instructions:
G07-CBO H. V. Mod kit
This mod gives you the ability to freely and smoothly adjust your image on the screen both horizontally and vertically.
Included is all the components to complete the modification
1 - 6.8K 3W resistor
2 - zero ohm jumper wires
1 - H. V. Adjustment board
***Unplug and discharge monitor before installation!!!
Installation instructions are as follows.
1. Desolder and discard R421, R507, R531 and R532
2. Solder in the 6.8k ohm 3W resistor from the kit in location R421
3. Fill the solder holes where R507 and R532 were
4. Desolder the two gray jumper wires from the chassis and discard
5. Install the two 0 ohm jumper wires provided in location R531 and between where the gray V. center wire was removed and the center vertical adjustment post
6. Attach the HV adjustment mod to the six adjustment posts from left to right with the corresponding wires
7. Remove the backing from the foam tape on the back of the adjustment board and attach into place
Note: Pots should already be adjusted to their Center for the first run, if not turn them to their mechanical centers. Afterwards adjust as needed.
Deep 6 Arcade LLC is not responsible and can not be held liable for any damage caused from either this kit or how you install it. By installing this kit you relinquish Deep 6 Arcade LLC from any and all liability.
If you are not training in working on CRT monitors, STOP and have a professional do it for you. Do not attempt to touch or work on any CRT monitors if you are not fully aware of how to safely handle and discharge them as well as perform work on them.
Image 1 of 5
Image 2 of 5
Image 3 of 5
Image 4 of 5
Image 5 of 5